Ad Code

Subscribe Us

500 watts mono Amplifier using 2SC5200 & 2SA1943

500 watts mono Amplifier using 2SC5200 & 2SA1943


This project is not for beginners. For make this project requires advanced level knowledge. Because this project cost is too high. So if you are a beginners, your little mistake can fail this project. 

This things are required to make this amplifier.


1. 5×2SC5200 Transistor.

2. 5×2SA1943 Transistor.

3. 1×D718 Transistor.

4. 1×B688 Transistor.

5. 1×TIP42 Transistor.

5. 2×2229 Transistor.

6. 2×A1015 Transistor.

7. 1×C1815 Transistor.


1. 2×47uf  capacitor 63/100v.

2. 2×100pf  capacitor 100v.

3. 2×470pf  capacitor 100v.

4. 2×474pf  capacitor 63/100v.

5. 1×0.1uf/104pf  capacitor 250/400v.


1. 10×0.22Ω resistor 5w.

2. 1×10Ω resistor 5w.

3. 2×100Ω resistor 1w.

3. 1×10Ω resistor 1w.

4. 1×4.7kΩ resistor 1w.

5. 1×4.7kΩ resistor 1/2w.

6. 10×10Ω resistor 1/2w.

7. 1×33Ω resistor 1/4w.

8. 3×150Ω resistor 1/4w.

9. 1×1kΩ resistor 1/4w.

10. 1×10kΩ resistor 1/4w.

11. 2×56kΩ resistor 1/4w.

12. 1×33kΩ resistor 1/4w.

13. 2×3.3kΩ resistor 1/4w.


1. 3×1N4007.

2. 1×Zener 24 volt 1w or 1/2w.

Power Supply

1. 1×KBPC3510.

1. 2×10000uf capacitor.

Watch this video for better understanding

In this post I make a 500 watt stereo amplifier board using 2SC5200 & 2SA1943 transistor. This amplifier can deliver 500 watts RMS at 4Ω. For power supply you can use 45-0-45 to 50-0-50 volt 10 Amp transformer. Now follow my steps for this amplifier. First we make pcb. For make pcb you need pcb layout. download the pcb layout and print it by laser printer on photo paper. Then cut the pcb layout. Then press the pcb layout by iron on copper clad board. Press the iron 10-15 munites. Then leave the pcb for cool down 10 munites. when the pcb was cool, put the pcb in water and move the pcb layout to copper clad board. Then put the pcb in ferric chloride [FeCl3+H2O] for etching 10-15 munites. when etching was end, clean the pcb by water. Then make hole on pcb. And then press the upper side print of pcb. Now your pcb is ready mount components by instruction.
When your amplifier is ready please test series lamp after input direct power

*Series light test..........Connect a 30-100w lamp with transformer's 220v ac line in series.

* Now test this amplifier.

1. Speaker output voltage.....0.00

2. Biasing voltage........0.4-0.7

3. Audio input voltage.......0.00

4. 2SC5200 collector voltage.........[+] positive volt.

4. 2SA1943 collector voltage.........[-] negative volt.

6. 2SC5200 & 2SA1943 base voltage.........0.1-0.2

7. 2SC5200 & 2SA1943 emitter voltage.........0.00

 Thank you,

Technical Mriganka.........

Post a Comment


  1. Sir bridge ractifair PCB ki lenth aur thight kitne senti miter hai

  2. Thanks for you effort.
    I was looking for the efficient and correct method for DIY the same.
    But everything belongs to business(pCB way & JLlbPcb etc) over the internet.
    Now my project begins.
    Thanks for spreading the knowledge

  3. descargando y vamos a fabricarla y despues comento como me fue

  4. Muy buen aporte, gracias por compartir sus conocimientos, un saludo

  5. board ko acche se scrub karr ke uske upar aralditev(2part epoxy) glue ka ek coating kar dena ... usse copper tracks ke upar oxidation nahi hoga .....

  6. sir kya aap hame is board me lagne wali sabhi components uplabd kara sakte h

  7. muchas gracias x el aporte haora solo keda poner manos ala obra

  8. sir is this only at 4 ohms speaker load.

  9. Good.. I made this amplifier. It's really work.. Thank you

  10. I make this amplifier. I have bias voltage 0.73v and Base of the 5200 - 221mv and 1943 - 60mv. Amplifire working. And heat is high. What is the fault.