1000 Watts R.M.S Mono power Amplifier

1000 Watts R.M.S Mono power Amplifier

Components►

1. 10×2SC5200 Transistor.
2. 10×2SA1943 Transistor.
3. 1×C5198 Transistor.
4. 1×A1941 Transistor.
5. 1×TIP42 Transistor.
6. 2×C2229 Transistor.
7. 2×A1015 Transistor.
8. 1×C1815 Transistor.
9. 2×47uF capacitor 63/100v.
10. 2×100pF capacitor 100v.
11. 2×470pF capacitor 100v.
12. 2×474pF capacitor 63/100v.
13. 1×0.1uF/104pF capacitor 250V.
14. 20×0.33Ω resistor 5w.
15. 1×10Ω resistor 5w.
16. 2×100Ω resistor 1w.
17. 1×10Ω resistor 1w.
18. 1×4.7kΩ resistor 1w.
19. 20×10Ω resistor 1/2w.
20. 1×33Ω resistor 1/4w.
21. 3×150Ω resistor 1/4w.
22. 1×1kΩ resistor 1/4w.
23. 1×4.7kΩ resistor 1/4w.
24. 1×10kΩ resistor 1/4w.
25. 2×56kΩ resistor 1/4w.
26. 1×33kΩ resistor 1/4w.
27. 2×3.3kΩ resistor 1/4w.
28. 3×1N4007
29. 1×Zener 24 volt 1w
30. 1×KBPC3510.
31. 4×10000uf capacitor 80V.

Watch this video for better understanding

License► ©Technical Mriganka. You can't use this pcb layout for commercial purpose. You can use this pcb layout only for educational and diy projects.

PCB LAYOUT►https://drive.google.com/folderview?id=10KSLyujHtWk4IH17Dul4vwtNOLQN56Jt

In this post I make a 1000 Watts R.M.S  amplifier using 2SC5200& 2SA1943 Transistor. Which can deliver upto 1000 Watts in R.M.S power at 4Ω. We test this amplifier, and we got it's frequency range 30hz-20khz. For power supply you can use 50-0-50V 15A toroidal transformer. Now follow my steps for this amplifier. First we make pcb. For make pcb you need pcb layout. download the pcb layout and print it by laser printer on photo paper. Then cut the pcb layout. Then press the pcb layout by iron on copper clad board. Press the iron 10-15 munites. Then leave the pcb for cool down 10 munites. when the pcb was cool, put the pcb in water and move the pcb layout to copper clad board. Then put the pcb in ferric chloride [FeCl3+H2O] for etching 10-15 munites. when etching was end, clean the pcb by water. Then make hole on pcb. And then press the upper side print of pcb. Now your pcb is ready mount components by instruction.

Please solder this two voltage line carefully. Because the copper line is too weak, it couldn't handle 1000 watts.

After mounting all components, when your board is ready. 

In the driver board and power transistor board you can see V+,V-,B+,B- and OUT. Now connect driver board with the power transistor board by wire. Wire gauge minimum 1.5mm.