Echo, Delay effect board for microphone.

Components

1. 1×PT2399 IC.
2. 1×4858D IC.
3. 4×1KΩ resistor 1/4W.
4. 3×10KΩ resistor 1/4W.
5. 5×15KΩ resistor 1/4W.
6. 2×4.7KΩ resistor 1/4W.
7. 2×47KΩ resistor 1/4W.
8. 1×680Ω resistor 1/4W.
9. 4×1N4007 Diode.
10. 1×Led 3 mm.
11. 1×8 pin IC base/ socket.
12. 1×16 pin IC base/ socket.
13. 5×0.1uF (104) capacitor 50/ 100V.
14. 2×0.0033uF (332) capacitor 50/ 100V.
15. 2×330pF (331) capacitor 50/ 100V.
16. 2×0.068uF (683) capacitor 50/ 100V.
17. 1×0.001uF (102) capacitor 50/ 100V.
18. 1×0.0056uF (562) capacitor 50/ 100V.
19. 2×560pF (561) capacitor 50/ 100V.
20. 6×0.47uF (474) capacitor 50/ 100V.
21. 1×7805 + voltage regulator.
22. 1×7812/ 7815 + voltage regulator.
23. 1×7912/ 7915 - voltage regulator.
24. 1×2 pin connector Base/ Socket 2.54 mm.
25. 2×3 pin connector Base/ Socket 2.54 mm.
26. 2×100uF capacitor 25V.
27. 2×2200uF capacitor 25V.
28. 3×Dual single turn potentiometer 100K.

License:- ©Technical Mriganka. You can't use this PCB Layout and Gerber File for commercial purpose. You can use this PCB layout and Gerber file only for Educational and DIY projects.

Gerber File - https://bit.ly/3skE6fB

PCB Layout & Schematic - https://bit.ly/3H223ww

PCB From PCBWay.com

Click here (PCBWay.com) - https://www.pcbway.com

PCBWay are the largest PCB manufacturer in China. They offer Standard PCB, Advanced PCB, Rigid-Flex PCB, SMD-Stencil and PCB Assembly Service. Here you get, 100x100mm 2 Layer PCB only at $5, And processing time within 24 hour. And they distribute, worldwide.

After one week I received my PCB. You can see the PCB quality, it's awesome. I ordered Red color PCB. But you can choose your PCB color. PCBWay provide total 9 color solder mask - green, blue, red, purple, black, white, yellow, matte black and matte green. On PCBWay you can get 100x100mm 2 Layer PCB only at $5. Maximum size PCB you can get 500x1100mm. And maximum Layer is up to 14 Layers. And If you order PCB first time at PCBWay, then you get a $5 discount coupon. So upload your Gerber today and get best quality PCB.

How to make PCB by ironing method

For make PCB you need PCB layout. Download the PCB layout and print it by laser printer on photo paper. Then cut the PCB layout. Then press the PCB layout by iron on copper clad board. Press the iron 10-15 minutes. Then leave the PCB for cool down 10 minutes. When the PCB will cool, put the PCB in water and move the PCB layout to copper clad board. Then put the PCB in ferric chloride [FeCl3+H2O] for etching 10-15 minutes. when etching will end, clean the PCB by water. Then make hole on PCB. And then press the upper side print of PCB. Now your PCB is ready, mount components by instruction.

How to test this preamplifier

Output & Input - Check Audio Output and Mic Input voltage. Here you get no voltages 0.00V. If you get same voltages, then connect this preamplifier to amplifier.