How to make bridge rectifier on 12-0-12 volt transformer.

How to make bridge rectifier on 12-0-12 volt transformer.

First you want 1 pcs 12-0-12 volt transformer

This things are required to make it..........

*👉 12-0-12 volt transformer...........https://amzn.to/2Ae0X0F

                 [Bridge rectifier]

*👉 For 5 Amp transformer............

     1.👉 4 pcs SR5100.........https://amzn.to/2Rk2Ena

     2.👉 1 pcs 4700uf 16-25 volt capacitor..........https://amzn.to/2Abnv24

*👉 For 2-3 Amp transformer............

     1.👉 4 pcs IN5408 diode..........https://amzn.to/2V84fLy

     2.👉 1 pcs 3330uf 16-25 volt  capacitor...........https://amzn.to/2AeIPnf

*👉 For 500mA -1 Amp transformer..........

     1.👉 4 pcs IN4007 diode........https://amzn.to/2RandCk


     2.👉 1 pcs 2220uf 16-25 volt capacitor..........https://amzn.to/2RebB0V

How to make it.........??

Watch this video for better understanding.

Circuit Diagram

*Watch this circuit diagram and follow my steps for make it.

*I am using here 1 ampere transformer but you can use this bridge rectifier wiring any ampere transformer. [Must change diode and capacitor when increase ampere on transformer]

*Then you want 4 pcs IN4007 diode (for 1 ampere transformer. must change diode when increase ampere on transformer).

*Hold diodes on the one hand of [+].

* Then hold diodes as well as this picture. 2 diodes[+] on the one hand and  2 diodes[-] on the one hand.

*Then joint pin of diodes as well as picture.

*watch the picture.

*Where 2 diodes [+] connected there output of DC 12 volt [-].

*Where 2 diodes [-] connected there output of DC 12 volt [+].

*And where 1 diode [+] and where 1 diode [-] connected there input ac 12 volt.

*Then solder pin of  diodes carefully.

*Then you want 2 pcs 1000uf capacitor. (for 1 ampere transformer. must change capacitor when increase ampere on transformer).

*Watch this picture about capacitor [+] and [-]. The blue portion of capacitor is positive and white portion of capacitor is negative.

*Then connect one capacitor [+] with one capacitor [-] as well as the picture. 

*Then watch this picture, left side where capacitor [-] there input and output of  DC 12 volt [-]. Right side where capacitor [+] there input and output of  DC 12 volt [+]. And where connected one capacitor [+] with one capacitor [-] there input and output of GND.

*Then connect the bridge rectifier with transformer. [where 1 diode [+] and where 1 diode [-] connected there input ac 12 volt].

*Then watch the picture Where 2 diodes [+] connected there output of DC 12 volt [-]. Where 2 diodes [-] connected there output of DC 12 volt [+]. And connect the ground wire middle pin of transformer.

*Then connect capacitors with transformer as well as picture. connect rectifier [+] to capacitor [+], connect rectifier [-] to capacitor [-] , and GND connect to where connected one capacitor [+] with one capacitor [-].

*Then connect a 3 mm led with 1k resistor. resistor connect [+] pin of led.

*And then led connect bridge rectifier. connect resistor where output of dc [+] 12 volt. And connect led [-] pin to GND.

*Then check voltage by multimeter.